This session focuses on particle emissions from combustion engines, including measurement methods and fuel effects. Presenter Leonidas D. Ntziachristos, Aristotle University Thessaloniki
EGR coolers are used in combustion engines to reduce NOx emissions. However, heat transfer in these coolers also results in thermophoresis-temperature-gradient driven motion of suspended particles towards cooler regions-which leads to significant soot deposition. Presenter Meisam Mehravaran
Some the OBD-II regulations have been around for a long time or seem to be intuitively obvious. It is easy to assume to assume that everyone knows how to implement them correctly, that is, until someone actually reads the words and tries to do it. Most often, these issues come up when modifying existing OBD features, not when creating completely new ones. This presentation contains a few examples of features that should have been easy to implement, but turned out not to be easy or simple. Presenter Paul Algis Baltusis, Ford Motor Co.
Several technological advancements have enabled hybrid technology to become a viable option in the commercial truck market. Although hybrid trucks are becoming more mainstream, they are not the right alternative fuel solution for every application. When matched with the right duty cycle, hybrid technology can provide a significant cost savings. Due to these advancements and anticipated benefits, hybrid commercial trucks are forecasted to become a significant part of the commercial truck market. Presenter Glenn Ellis, Hino Motors Sales USA Inc.
Diesel Dual Fuel, DDF, is a concept which promises the possibility to utilize CNG/biogas in a compression ignition engine maintaining a high compression ratio, made possible by the high knock resistance of methane, and the resulting benefits in thermal efficiency associated with Diesel combustion. Presenter Fredrik K�nigsson, AVL Sweden
Developing relatively cheap and widely available resources for heterogeneous solid catalyst synthesis is a promising approach for biodiesel fuel industry. Seashell which is essentially calcium carbonate can be used as a basic support for transesterification heterogeneous catalysts. In the present investigation, the alcoholysis of waste frying oil has been carried out using seashell-supported K3 PO4 as solid catalyst. Presenter Essam Oun Al-Zaini, PhD student, UNSW
The basics of propane gas used as an automotive fuel. Topics include what propane is, how it is priced, how fleet obtain it and the basics on propane fueling infrastructure and employee training. Presenter Nathan Ediger, Ferrellgas
Learn how the U.S. Department of Energy's Clean Cities Program can help with the deployment of alternative fuel and advanced technology school buses. Presenter Mark S. Smith, US Department of Energy
Propane autogas, the world?s third most-used engine fuel, powers vehicles, transit buses, and now school buses. Blue Bird has recently launched the Next Generation Vision type C school bus, powered by a ROUSH CleanTech liquid propane autogas fuel system and a Ford 6.8L V10 engine. The bus reduces operating costs by up to 40%, greenhouse gas emissions by up to 24%, and maintains the factory horsepower, torque, and towing capacity ratings. Learn about how school districts are saving over $.30 / mile using this clean, domestically-produced fuel. Presenter Brian Carney, Roush CleanTech.
Powertrain Systems development is facing unprecedented challenges driven by the convergence of many factors: increasing government regulations for tailpipe emissions, diagnostics and fuel economy, increased competition, shorter development cycles, and tighter program budgets. Using telematics and information technology to automate the evaluation of a system�s robustness enables engineers to focus their time on problem areas during their normal development process and launch with quality. This presentation will use real world examples to detail how this methodology was jointly applied by Control-Tec and Ford Motor Company to identify and improve the system performance of Ford�s Air-Fuel Imbalance Monitor before production. Presenter Bill Leisenring, Control-Tec LLC
Plug-In Hybrid and Extended Range Electric Vehicle's have quickly become the focus of many OEM's and suppliers. Existing regulations and test procedures did not anticipate this rapid adoption of this new technology, resulting in many product development challenges. The lack of clear requirements is further complicated by CARBs consideration of CO2 inclusion in their next light duty OBD regulation. This presentation provides an overview of the regulatory requirements for OBD systems on hybrid vehicles that intend to certify in California. Near term challenges for EREV?s and PHEV?s are discussed, including concerns with the existing denominator and warm-up cycle calculations. Some proposals are made to address these concerns. Presenter Andrew Zettel, General Motors Company
Sensing exhaust gas temperature is a key component in diesel after treatment systems for both control and diagnostics. Accuracy varies significantly depending upon the sensing technology and implementation in the system. Prior published work has demonstrated that resistance based temperature sensors are not able to achieve the system accuracy required for advanced diagnostics over the life of the emission system. This presentation will show that it is feasible to achieve better than �10�C end of life system accuracy by means of active thermocouple technology. Results from tests at Michigan Technological University will be used to illustrate diagnostic uncertainty related to the application of temperature sensors and a specific DOC/DPF example will be used to show the benefits of accurate temperature based diagnostics. Presenter D. P. Culbertson, Watlow Gordon
OBD requirements for aftertreatment system components require monitoring of the individual system components. One such component can be an NH3-SCR catalyst for NOx reduction. An OBD method that has been suggested is to generate positive or negative spikes in the inlet NH3 concentration, and monitor the outlet NOx transient response. A slow response indicates that the catalyst is maintaining its NH3 storage capacity, and therefore it is probably not degraded. A fast response indicates the catalyst has lost NH3 storage capacity, and may be degraded. The purpose of the work performed at Southwest Research Institute was to assess this approach for feasibility, effectiveness and practicality. The presentation will describe the work performed, results obtained, and implications for applying this method in test laboratory and real-world situations. Presenter Gordon J. Bartley, Southwest Research Institute
A combination of laboratory reactor measurements and vehicle FTP testing has been combined to demonstrate a method for diagnosing the formation of NO2 from a diesel oxidation catalyst (DOC). Using small cores from a production DOC and simulated diesel exhaust, the laboratory reactor experiments are used to support a model for DOC chemical reaction kinetics. The model we propose shows that the ability to produce NO2 is chemically linked to the ability of the catalyst to oxidize hydrocarbon (HC). For thermally damaged DOCs, loss of the HC oxidation function is simultaneous with loss of the NO2 production function. Since HC oxidation is the source of heat generated in the DOC under regeneration conditions, we conclude that a diagnostic of the DOC exotherm is able to detect the failure of the DOC to produce NO2. Vehicle emissions data from a 6.6 L Duramax HD pick-up with DOC of various levels of thermal degradation is provided to support the diagnostic concept.
Revisions to the California OBD-II diesel regulations required many updates to various SAE and ISO on-board diagnostic standards; these include major revisions to SAE J1979, J1699-3, J2012 and J1930. This presentation is intended to review the background for these changes as well as the revisions made in these documents. Presenter Robert Gruszczynski, Volkswagen of America
The OBD approval process can be a frustrating time for both manufacturer and ARB staff. For manufacturers, a long approval process can sometimes mean accepting deficiencies prematurely in exchange for an approval. For ARB staff, they are inundated with highly technical information which they must review, garner understanding of and then apply their experience to evaluate it for compliance. OBD approval anxiety can be minimized, if not avoided, when manufacturers understand ARB�s expectations. This presentation will take you through some unwritten rules and common pitfalls which can impede the approval process, thus providing a guideline to a less painful and more efficient certification document review and approval. Presenter Mark Frank, Winterpark Engineering Llc